Alcatel 4400 Rel3.2 PBX with Cisco CallManager (CCM) Using 6608-E1 QSIG Protocol as MGCP Gateway Table Of Contents Application Note Alcatel 4400 Rel3.2 PBX with Cisco CallManager (CCM) Using 6608-E1 QSIG Protocol as MGCP Gateway This application note illustrates connectivity for Alcatel 4400 Release 3.2 PBX with Cisco CallManager using Cisco 6608-E1 QSIG as MGCP Gateway. Introduction Key attributes of the network environment used for this application note:.

1. Alcatel Ccsupervision Software For Mac
2. Alcatel Ccsupervision Software For Mac®
3. Alcatel Software For Pc

The network topology diagram shows the test set-up for end-to-end interoperability with the Cisco CallManager (CCM) connected to the PBX via 6608-E1 QSIG link as MGCP Gateway. Connectivity is achieved by using the PRI ISO QSIG E1 protocol type on the MGCP gateway and ABC-F (ISO version) as protocol type on the Alcatel 4400 PBX. Basic Calls worked fine in both directions with Calling/Connected Name and Calling Number features support. Alcatel 4400 PBX does not honor Connected Number Identification Presentation feature. Alcatel phone does not display Connected Number even though CCM is sending the information in the connect message.

Call Forwarding did not work when the IP phone calls an Alcatel phone that is setup to forward to another Alcatel phone. Network Topology Figure 1 Network Topology or Test Setup. Limitations Calling Name and Number Feature When calling from Alcatel digital phone to Cisco 7960 IP phone, the Cisco IP phone displays Calling Name and Number when the call is answered. Alcatel phone however displays connected Name only, No connected Number when the call is answered.

Alcatel Ccsupervision Software For Mac

Alcatel does not honor Connected Number Identification Presentation QSIG service even though CCM is sending the Connected Number information in the connect message. CCM Seaview release does not support sending Alerting Name or Busy Name Identification information. Call Forwarding Calls did not complete when the IP phone calls an Alcatel phone that is setup to forward to another Alcatel phone. Alcatel in this case sends Facility IE for 'CallRerouting'. Since CCM3.3 Seaview release does not support CallRerouting, the call is not completed.

As shown in, an Alcatel 4400 PBX was connected via an ISDN E1 PRI QSIG link to a Cisco 6608-E1 Gateway, which in turn, was connected to an Ethernet switch. The interoperability testing involved Layers 1, 2 and 3 on the ISDN PRI QSIG link between a Cisco 6608-E1 and the PBX. Layer 1 (Physical Layer) The Alcatel 4400 PBX configuration screen for the ISDN PRI QSIG trunk interface is reached using both Alcatel Board and Board Digital Access menus, setting the PRI physical layer parameters. Layers 2 & 3 (Q.921 and Q.931) Layer 2 and 3 packet exchanges were monitored using an Acacia Clarinet protocol analyzer, bridged across the PRI link in high impedance mode. Layer 2 Q.921 packets were monitored to ensure that each PBX/6608-E1 software configuration properly exchanged SABME/UA packets to initialize the ISDN link, and then RR packets were exchanged every 30 seconds. Layer 3 Q.931 packets were monitored to ensure that the appropriate call setup/teardown packets were exchanged for each configuration, and that the SETUP packets contained the mandatory Information Elements with the necessary details, as well as optional IEs such as Calling Name and Number. Telephone calls were made end-to-end in both directions through the Cisco 6608-E1 Gateway, and a check was made to ensure that there was an audio path in both directions for each call.

User/Network Settings The Cisco 6608-E1 Gateway with ISDN protocol type setting of PRI ISO QSIG E1 supports both protocol sides by selecting 'Network/User' in the Protocol Side field when configuring the Gateway via CCM. The Alcatel 4400, supports both 'USER' (slave) and 'NETWORK' (master) protocol sides. Network/User options are set in the Board/Digital Access Options menu. Network mode must be set to Yes for (Master/Network) or No - (Slave/User). The following options for Alcatel PBX are of particular interest:.

Trunk interface type must be set to PRA2. Access Type must be set to T2. Q931 signal variant is used to determine Protocol type. This option was set to ABC-F. Appendix B Test Results Testing was performed by Test Engineer(s): Samir Batio, July 24, 2002 Retesting with CCM3.3-256c load was performed by Test Engineer: Samir Batio, October 1, 2002 Test Setup 1 Test setup was as follows:. PBX1 configured as ISO version ABC-F, emulates Network.

• Review the software license agreement, and then click Continue. Aplikasi office free. • Select Agree to agree to the terms of the software license agreement. • Choose how you want to install Office and click Continue.

Cisco 6608-E1 Gateway configured as PRI ISO QSIG E1, emulates User.

Alcatel Ccsupervision Software For Mac®

Files32.com collects software information directly from original developers using software submission form. Sometimes it can happen that software data are not complete or are outdated.

Alcatel Software For Pc

You should confirm all information before relying on it. Using crack, serial number, registration code, keygen and other warez or nulled soft is illegal (even downloading from torrent network) and could be considered as theft in your area. Files32 does not provide download link from Rapidshare, Yousendit, Mediafire, Filefactory and other Free file hosting service also. The software has been submitted by its publisher directly, not obtained from any Peer to Peer file sharing applications such as Shareaza, Limewire, Kazaa, Imesh, BearShare, Overnet, Morpheus, eDonkey, eMule, Ares, BitTorrent Azureus etc.